The MYD-AM437X Development Board is a complete evaluation platform for Texas Instruments (TI) Sitara AM437x family (AM4376, AM4377, AM4378 and AM4379 ) of ARM Cortex-A9 Microprocessors (MPUs) with optional 3D graphics acceleration and a quad-core Programmable Real-time Unit (PRU) as well as dual camera support. Typical applications are patient monitoring, navigation equipment, industrial automation, portable data terminals, bar code scanners, point of service, portable mobile radios, test and measurement and more others.

The MYD-AM437X development board is using the MYC-AM437X CPU Module as the core controller board which integrates the core components including the AM437x processor, 512MB DDR3, 4GB eMMC, 32KB EEPROM, Gigabit PHY and PMIC (TPS65218). The MYC-AM437X CPU Module is mounted onto the MYD-AM437X base board through two 0.8mm pitch 2*50-pin board-to-board connectors. In addition to those functions provided by the CPU Module, the base board has extended a rich set of peripherals through headers and connectors from the SOM and some extended controller chips including two serial ports, four USB Host ports, one USB Device port, dual Gigabit Ethernet ports, one CAN, one RS485, two camera interfaces, one Micro SD, HDMI, LCD, Touch screen and more others.

The MYD-AM437X board series have four models with different AM437x processors. They are sharing the same pin-out with software fully compatible. And the minor differences are mainly from the processors features.

The MYD-C437X board is able to run Linux OS. It is delivered with some necessary cable accessories and a product disk containing Linux 3.12.10 software packages and detailed documents. MYIR also offers optional 4.3- and 7-inch LCD module (with touch screen), USB based Wi-Fi and Camera modules and BUS based Camera modules for the MYD-C437X board. The complete platform provides a quick AM437x starter kit for users when getting the goods out-of-the-box right away.

Features:

Mechanical Parameters:

Dimensions: 177mm x 106mm (base board), 60mm x 45mm (CPU Module)

PCB Layers: 4-layer design (base board), 8-layer design (CPU Module)

Power supply: +5V/2A (base board), +5V/0.33A (CPU Module)

System static power: about 5V/0.2A (base board), about 5V/0.7A (base board + CPU module)

about 5V/1.1A (base board + CPU module + 4.3-inch LCD)

about 5V/1.2A (base board + CPU module +7-inch LCD)

Working temperature: 0~70 Celsius (commercial grade) or -40~85 Celsius (industrial grade)

Processor:

TI AM437x (AM4376, AM4377, AM4378 and AM4379)

- Up to 1GHz Sitara ARM Cortex-A9 32-Bit RISC processor

- POWERVR SGX Graphics Accelerator subsystem for 3D graphics acceleration to support display and gaming effects

- Single-cycle vector floating point (VFP)

- Dual camera and display processing subsystem

- Cryptographic acceleration and secure boot

- PRU-ICSS enables simultaneous industrial Ethernet protocols and motor feedback protocols

- Support for 32 bit LPDDR2/DDR3/DDR3L

- Low power: ~5mW deep sleep and < 0.1mW RTC-only

- Simplified power sequence for flexible power design

Memory:

512MB DDR3 SDRAM (256MB is optional)

4GB eMMC Flash (reserved 256/512MB Nand Flash design)

16MB QSPI Flash (reserved design, not soldered)

32KB EEPROM

Peripherals and Signals Routed to Pins:

Power Management IC (TPS65218B1RSLR)

Gigabit Ethernet PHY

One power indicator (Red LED)

One user LED (Green)

Two 0.8mm pitch 100-pin board-to-board expansion connectors can carry out interfaces below:

- 2 x USB

- 6 x Serial ports

- 2 x I2C

- 2 x CAN

- 2 x SPI

- 14 x ADC (8 channels from ADC1 and 6 channels from ADC0)

- 3 x SDIO

Serial ports:

- 1 x 5-wire RS232 Debug serial port (DB9)

- 1 x 5-wire RS232 serial port (UART1)

- 1 x RS485 (with isolation)

USB:

- 4 x USB2.0 Host ports

- 1 x Mini USB2.0 Device port

2 x 10/100/1000Mbps Ethernet interfaces

2 x CAN interface (with isolation)

1 x TF card slot

1 x HDMI output interface

1 x LCD interface (16-/24-bit true color, supports optional 4.3-inch and 7-inch TFT LCD)

2 x Camera interfaces (0.5mm pitch 30-pin FPC connectors)

1 x 4-wire resistive touch screen interface

1 x Audio input port (3.5mm jack, do not provide driver at present)

1 x Stereo Audio output port (3.5mm jack, do not provide driver at present)

1 x 2.54mm pitch 20-pin JTAG interface

4 x Buttons (1 x Reset button, 1 x PMIC, 2 x User buttons)

1 x Power indicator (Red LED)

3 x User LEDs (Blue)

2 x 2.0mm 20-pin expansion connectors

- 8 x ADC

- 2 x SPI

- 2 x I2C

- 2 x UART

OS Support:

Linux 3.12.10